ISL-4800 Image Sensor Tester

The Jova Solutions ISL-4800 is the highest performance interface and test solutions available for image sensors, digital cameras and video devices. This single piece of hardware supports nearly every sensor, camera, and video source interface standard in existence. A fully integrated, off-the-shelf, hardware/software tester package, ISL-4800 provides a full range of interfaces, controls, advanced image analysis test routines, evaluation and characterization capabilities in one easy-to-use, inexpensive, small-footprint solution. The ISL-4800 is a powerful, affordable, flexible, and expandable solution that supports future requirements with field upgradable FPGA code and a flexible interface board architecture. 

HIGH PERFORMANCE

FOR HIGH VOLUME PRODUCTION, TEST AND DESIGN

  • Rugged and Robust down to smallest details such as built-in isolation relays and voltage level buffers
  • Reduce test times and increase test coverage with built-in instrumentation
  • Rapid deployment and field reprogrammable
  • Integrated LED control
  • Ability to integrate with a production wafer prober
  • Automation software API (DLL, LabVIEW, TestStand)

The ISL-3200 contains embedded programmable power supplies, an integrated master clock, sensor I2C/SPI communications, and integrated frame capture electronics. The Image Sensor Lab ISL-3200 hardware also comes with the Image Sensor Lab application software, which provides full control over the ISL-3200 hardware, as well as sensor control and communications. Image Sensor Lab application software also includes a powerful scripting engine for automating common configuration setups or mode changes. Simple histogram analysis and raw pixel data analysis are provided by the Basic version, with many additional analysis routines available in the optional advanced package.

SPECIFICATIONS

I2C/SPI Sensor Communications 

  • Adjustable I2C clock rate to 1MHz. (including standard 100KHz and 400KHz)
  • SPI communications up to 10 MHz
  • Create, save and execute customer I2C scripts

 Built-in Power Supplies 

  • Four (4) 1.25V to 4.0V 100mA Power Supplies
  • Two (2) 0.6V to 1.8V 600mA Power Supplies
  • Two (2) 1.2V to 3.4V 600mA Power Supplies
  • One (1) 0V to 10V 600mA Utility Power Supply
  • Two (2) 3.3V On/Off Power Supplies
  • 12-bit and 24-bit Voltage and Current Measurement

Programmable Master Clock 

  • Programmable between .001 MHz and 68 MHz.
  • Optional FPGA Clock Doubler
  • External Clock Input

Parallel Image Capture 

  • 8-bit or 16-bit image capture
  • Output Formats: RAW, Bayer, YCbCr(YUV), RGB, RGB565, RGB555, RGB444
  • ROI Capture
  • Double Buffered
  • Video Rate Sequential Image Capture

High-Speed Serial Image Capture 

  • MIPI CSI-2  1,2 and 4 lane support, up to 960 Mbps/lane
  • SMIA CCP2 Class 0,1, and 2 support, up to 650 Mbps
  • 24 LVDS high-speed serial pairs
  • Video Rate Sequential Image Capture

Additional Digital I/O

  • 48 Total Digital I/O (Including Sync and Data Lines)

Host Interface

  • 4xPCI Express Interface with 256 MBytes Memory
  • External Clock Input

Optional Built-in Volt-Ohm Meter 

  • 2 X 80 Analog Switch Matrix
  • Short/Open Test Capability
  • 12-bit and 24-bit Volt and Ohm Measurements

Powerful Data Interpretation 

  • Bit Masking in FPGA
  • Bit Swizzling in FPGA
  • Accomodates many data output formats and encodings
  • Supports CMOS image sensors from most manufacturers
  • Analog and MIPI sensor support through adapter board